Standard zees, cees and Eave Struts

Zees

A = long lap (All holes seen in Picture)
H = Short Lap (does not include black holes in Picture)

Holes are 9/16″ in diameter
Slots are 9/16″ x 7/8″

Dotted lines on 2nd flange hole represent oversized holes for E-Z lap.

Description Finish Weight/LF
12 ga. 8″ zee/cee Red Oxide 4.86
12 ga. 8″ zee/cee G-90 5.29
14 ga. 8″ zee/cee Red Oxide 3.55
14 ga. 8″ zee/cee G-90 3.83
15 ga. 8″ zee/cee Red Oxide 3.15
16 ga. 8″ zee/cee Red Oxide 2.85
12 ga. 10″ zee Red Oxide 6.23
14 ga. 10″ zee Red Oxide 4.56
14 ga. 8″ eave strut Red Oxide 4.82
14 ga. 8″ eave strut G-90 5.20

Total lineal footage of the same type gauge is used to determine the per foot cost of that quantity of zees/cees.

Zees are roll formed in lengths from 7 feet to 35 feet; length under 7 feet require special pricing.

 

Channels
OHD – Over Head Door
Blank Channels may not be available.

Part No. Description WT
CHA-A4-071112 8′ wide OHD header 28.3
CHA-A4-091112 10′ wide OHD header 35.4
CHA-A4-111112 12′ wide OHD header 42.5
CHA-A4-131112 14′ wide OHD header 49.6
CHA-A4-151112 16′ wide OHD header 56.7
CHA-A4-171112 18′ wide OHD header 63.8
CHA-A4-191112 20′ wide OHD header 70.9
CH2904 6′-4″ wide OHD header 21.4
CH2905 3′-4″ wide OHD header 11.3
CHADA4-090100 8′ high OHD jamb 32.3
CHAFA4-110100 10′ high OHD jamb 39.4
CHAHA4-130100 12′ high OHD jamb 46.5
CHAKA4-150100 14′ high OHD jamb 53.6
CHAMA4-170100 16′ high OHD jamb 60.7
CHAPA4-190100 18′ high OHD jamb 67.8
CHASA4-210100 20′ high OHD jamb 74.9
CHA-A4-070114 7′-2″ high OHD jamb 25.4
CHA-A4-250000 Framing channel 88.8
CHA-A4-200000 Framing Channel 71.0
CH2885 2′ OHD jamb extension 10.4
CH2886 4′ OHD jamb extension 17.2

 

Eave Struts


* 4 hole end pattern is available upon request.

Punch Patterns

N – low side eave strut
R – high side eave strut
B – low side w/3’6″ roof ext.
C – low side w/6’6″ roof ext.
Q – high side w/3’6″ roof ext.
P – high side w/6’6″ roof ext.

Part No. Description WT
ESN-N4C191112 Eave Strut 1:12, 20′ interior Bay 96.3
ESN-N4J191112 Eave Strut 4:12, 20′ interior Bay 96.3
ESN-N4C241112 Eave Strut 1:12, 25′ interior Bay 120.4
ESN-N4J241112 Eave Strut 4:12, 25′ interior Bay 120.4
ESN-N4C291112 Eave Strut 1:12, 30′ interior Bay 144.5
ESN-N4J291112 Eave Strut 4:12, 30′ interior Bay 144.5
ESN-N4C200010 Eave Strut 1:12, 19′ end Bay 96.7
ESN-N4J200010 Eave Strut 4:12, 19′ end Bay 96.7
ESN-N4C250010 Eave Strut 1:12, 24′ end Bay 120.8
ESN-N4J250010 Eave Strut 4:12, 24′ end Bay 120.8
ESN-N4C300014 Eave Strut 1:12, 29′ end Bay 145.0
ESN-N4J300014 Eave Strut 4:12, 29′ end Bay 145.0

 

Part Numbering

1– To order a 14 ga. zee with standard long lap holes punched, 25′ 2-1/2″ long:

ZEA-A4-250208

 Z Z = Zee
E E = 8″ x 2.5″
T = 10″ x 3.5″
A Lead Punch Pattern*
– X = special punch
Z = E-Z lap
A Trailing Punch Pattern*
4 2 = 12 ga. 4 = 14 ga.
5 = 15 ga. 6 = 16 ga.
– Slope code (not req’d on zees)
25 Length in Feet
02 Length in inches
08 Length in sixteenth inches

* Dean has a very extensive list of Standard hole patterns available at no extra charge. But special patterns can also be punched, if necessary (special pricing required).

 

2- To order a 14 ga. channel with A pattern holes punched, 9′ 11-3/4″ long:

CHA-A4-091112

 C C = Channel
H H = 8″ x 2.5″
F = 8″ x 2.5″
T = 10″ x 4″
A Lead Punch Pattern
– Hole location for header.
– = no holes
A Trailing Punch Pattern
4 2 = 12 ga. 4 = 14 ga.
5 = 15 ga. 6 = 16 ga.
– Slope code (not req’d on cees)
09 Length in Feet
11 Length in inches
12 Length in sixteenth inches

 

3- To ordera 14 ga. low side eave strut for a 1:12 pitch buildings, 20′ 00-5/8″ long:

ESN-N4C200010

 ES E = Eave Strut
N Lead Punch Pattern*
– n/a
N Trailing Punch Pattern*
4 2 = 12 ga. 4 = 14 ga.
5 = 15 ga. 6 = 16 ga.
C A = < .5:12 C = (.5 to < 1.75):12
E = (1.75 to < 2.75):12 G = (2.75 to 3.75):12
J = (3.75 to 4):12
20 Length in Feet
00 Length in inches
10 Length in sixteenth inches

 
Angles
 

Part No. Finish length/Size weight

Shelf Angle
(2) 9/16″ holes 3″ apart 5′ off center

 AN1002 Red Oxide 3″x3″x3/16″ 20′ long 74.2
AN1004 Red Oxide 4″x4″x1/4″ 20′ long 132.0


Sill/Rake Angle

 AN1219 GNZ 3″x2″
14 ga.
21′ long		 22.71
AN1120 GNZ 2″x5″
14 ga.
10′ long		 34.9
AN1116 GNZ 7″x5″
14 ga.
10′ long		 31.7

Flange Braces

 ANF4-FFIISS
FF length in feet
II length in inches
SS length in sixteenths		 Red OxideGNZ up to 6 feet 0.845/lf

Peak Diaphragms

 ANF4-FFIISS
FF length in feet
II length in inches
SS length in sixteenths		 Red OxideGNZ 0.5:12 use 020115
1:12 use 020204
1.5:12 use 020210
2:12 use 020214
3:12 use 020305
4:12 use 020310
5:12 use 020312		 0.845/lf

 
Clips
 

Part No.

 Finish Length/Size Weight (lbs)

Girt clip Endwall to Sidewall Connection		 CH2621 Red Oxide 11 ga.9/16″ hole with
6″ & 4 ” spacing
 4.1

Endwall girt to Sidewall Connection		 CL3002 Red Oxide 3/16″ Plate9/16″ hole with
4″ & 2.5″ spacing
 10.5

Door jamb base clip		 CL3009 Red Oxide 3/16″ plate3/4″ & 9/16″ hole
3″ & 4″ spacing		 1.3

Girt clip & door clip angle		 CL3010 Red Oxide 11 ga.9/16″x1.25″ slots 1.56

Girt to masonry clip		 CL3012 Red Oxide 11 ga.9/16″ & 1.25″ slots
4″ spacing		 .9

Door jamb to girt or Eave strut
 CL3013 Red Oxide 3/16″ plate9/16″ & 1.25″ slots 2.4

Friction clip – Girt to jamb		 CL3016 Red Oxide 11 ga.9/16″ hole with
4″ and 5.5″ spacingincludes (2) 0.5″x1.25″ bolts and nuts for fastening to the jamb.		 2.3

Insert girt clip		 CL3185 Red Oxide 3/16″ plate9/16″ hole 3.0

Purlin to Purrlin clip		 CL3169 Red Oxide 3/16″ plate9/16″ hole with
4″ & 2 ” spacing		 4.6

Door jamb to Rafter clip		 CL3047 Red Oxide 3/16″ plate9/16″ hole
4″ spacing		 2.3

Channel to Channel clip		 CL3063 Red Oxide 3/16″ plate9/16″ hole
 2.5

Insert girt clip (@ SM RF corner col.)		 CL3001 Red Oxide 3/16″ plate9/16″ & 1.25″ slots 3.1

Slide door header clip		 CL3000 Red Oxide 3/16″ plate9/16″ hole 4.5

Slide door track hanger		 CL3024
(w/8″ CH)		 Red Oxide 5/16″ plate9/16″ & 1″ slots
1.84

Slide door track splice clip		 CL3025 Red Oxide 5/16″ plate9/16″ & 1″ slots
1.25″ spacing		 4.6

 

Leave a Reply

Proudly powered by WordPress